LY71

-

1 or 2 axes (2-axis add function available; addition only is displayed when adding)

7 digits and minus display, Color amber

Current (1st axis, 2nd axis, addition axis), maximum, minimum and peak-to-peak values

Standard : 0.1 μm, 0.5 μm, 1 μm, 5 μm, 10 μm, 1 s, 10 s, 1 min, 10 min
Expanded : 100 μm, 50 μm, 25 μm, 20 μm, 2 μm, 0.05 μm, and 1 degree can be added.

Measuring unit input resolution or higher and supported inch units

A/B quadrature signal, Z signal (Conforms to EIA-422)

Measuring unit disconnected, Excess speed, Maximum display amount exceeded, Power failure, Error in stored data

Current value reset, Alarm cancel

The master calibration value is relocated when going past the reference point after the power is turned on.

It is possible to store/edit one value for each axis (when not using the master calibration function).

Selectable from latch and pause
Latch : Display held while latched (Display hold)
Pause : Peak calculation stopped while paused (Peak calculation hold)

A fixed compensation amount is applied to the measuring unit's count value. Compensation amount Standard: ±600 μm/m (Expanded: ±1000 μm/m)

0.100000~9.999999

Expansion board for BCD (option:LZ71-B), available 1 or 2 pics.
Expansion board for comparator (option:LZ71-B)

DC 12 V Rating 0.75 A Max. 1 A AC 100 V to 240 V ±10 % When using the AC adaptor PSC-22 (For U.S. only) or PSC-23 (For Europe and other countries) *Option

MAX. 32 VA connected at the AC adaptor.

Operating : 0~40°C (non condensing) Storage : -20~60°C (non condensing)

Approx. 1.5kg

LY72

Applications as gauge (set axis labels A, B, and C)

1~3axis

7 digits and minus display, Color amber

Current (1st axis, 2nd axis, addition axis), maximum, minimum and peak-to-peak values

Current (1st axis, 3rd axis, addition axis)

Standard : 0.1 μm, 0.5 μm, 1 μm, 5 μm, 10 μm, 1 s, 10 s, 1 min, 10 min
Expanded : 100 μm, 50 μm, 25 μm, 20 μm, 2 μm, 0.05 μm, and 1 degree can be added.

Measuring unit input resolution or higher and supported inch units

A/B quadrature signal, Z signal (Conforms to EIA-422)

Measuring unit disconnected, Excess speed, Maximum display amount exceeded, Power failure, Error in stored data

Current value reset, Alarm cancel

Restart of peak value calculation for each axis/all axes

It is possible to store/edit up to three values for each axis.

The master calibration value is relocated when going past the reference point after the power is turned on.

It is possible to store/edit one value for each axis (when not using the master calibration function).

Selectable from latch and pause
Latch : Display held while latched (Display hold)
Pause : Peak calculation stopped while paused (Peak calculation hold)

Display hold

A fixed compensation amount is applied to the measuring unit's count value. Compensation amount Standard: ±600 μm/m (Expanded: ±1000 μm/m)

0.100000~9.999999

Data format: All axes on same line/New line for each axis Peak-to-peak value
Transfer rate:38400/19200/9600/4800/2400/1200bps
Parity: None/Odd/Even, Stop bit : 1 or 2, Data length: 8 bits or 7 bits

DC 12 V Rating 0.75 A Max. 1 A AC 100 V to 240 V ±10 % When using the AC adaptor PSC-22 (For U.S. only) or PSC-23 (For Europe and other countries) *Option

MAX. 32 VA connected at the AC adaptor.

Operating: 0~40°C (non condensing) Storage: -20~60°C (non condensing)

Approx. 1.5kg