Magnescale Interface

MG10series Specifications
Model		MG10-P1
Power	Power supply Power supply voltage	DC12~24V(11~26.4V) Min. startup time: :100ms or less
	Power consumption	2.0W + total power consumption for connected modules*1
	Imrush current (10ms)	10A or less (when maximum number of modules are connected)
	Power supply reverse connection prevention	Fuse (5A fuse is built in.)
Communication	I/F input/ output circuit	RS-232C (Conforms to EIA-232C)
	Baud rate setting	2400/9600/19200/38400 bps (set with DIP switch)
	Data length	7/8 bit (set with DIP switch)
	Stop bit	1/2 bit (set with DIP switch)
	Parity	None/ODD/EVEN (set with DIP switch)
	Delimiter	CR/CR+LF (set with DIP switch)
Linkage function	Maximum number of linkages	max.16 (total of counter modules 64)
Linkage function	Maximum length of linking cable	max.10m
I/O	Input format	source input (+COM)
	Input format	Photo coupler insulation DC 5~24V
	Output format	sink type (-COM)
	Output format	Photo coupler insulation DC 5~24V
	Input signal	reset, pause, start, latching, and data out trigger to whole channels
	Output signal	integrated alarm
Connectable modules	Counter modules	MG20-DK, MG20-DG, MG20-DT (available for mixed use, up to 16 modules) *1
Connectable modules	Interface modules	MG30-B1, MG30-B2 *1
*1 Total power of modules connected to MG10 should not be over 54W (12VDC Input) or 108 W (24VDC Input).

MG20series Specifications
Model		MG20-DK	MG20-DG	MG20-DT
Power consumption		1W + total power consumption for connected measuring units	1.4W (when connected DG-B series) 0.5W (when connected DL-B series)	0.8W
Measuring unit input	Connectable measuring units	DKseries (A/B quadrature input)	DGB series, DLB/DL**BR series	DT series
	Allowable resolution setting *2	10/5/1/0.5/0.1μm	10/5/0.5μm	5μm(DT12/32) 1μm(DT512)
		set with DIP switch
	Maximum response speed	Subject to the specification of the connected gauge		1m/s
	Maximum accelation speed	Subject to the specification of the connected gauge		2400m/s²
	Reference point *3	REF-LED (reference point loaded) shows on the display after the reference point is detected. Set "0" or preset value on the counter when the reference point is detected.		-
Others	Alarm	S-ALM LED activates by excess speed / acceleration of measuring unit. C-ALM LED activates by excess speed of the internal circuit of counter.
		Alarm display is cancelled by reset command from MG10 or with the reset button of main unit.
2 Set the resolution value of the connected gauge. 3 MG20-DG work only connect to DL**BR series

MG30series Specifications
Model		MG30-B1
Power consumption		1W
I/O	Input format	source input (+COM)
		Photo coupler insulation DC 5~24V
	Output format	sink type (-COM)
		Photo coupler insulation DC 5~24V
	Input signal	DRQ / channel address / measuring mode shifting / comparator shifting / reset / start / posing / reference point loaded
	Output signal	BCD data (6 digits) / READY / code / GO/NO GO output / alarm / reference point loaded
Output setting		timer (1~128ms) / OUT / OR / polarity (set with internal DIP switch)

MGseries Specifications
Operating temperature/humidity	0 ~ +50°C(non condensing)
Storage temperature/humidity	-10 ~ +60°C(20 ~ 90%RH)